Rossmax HS200 Blood Sugar Test Strips For Diabetes Management, Pack of 50's

• Blood glucose test strips for self-testing and single use
• Benefits diabetic patients for diabetes control
• For quantitatively measuring glucose in whole blood
• To be used 6 months after opening
• 22 months life span
• Test time: 5 seconds
• Only works with Rossmax HS200 glucose meter
• Measuring method: Advanced GDH-FAD Auto coding Technology
• Measuring range: 20~600 mg/dL (1.1 ~ 33.3mmol/L)
• Blood source: fresh whole capillary blood
• Volume of blood: min 0.7l
• Pack contains 1 vial of 50 strips

Rossmax HS200 Blood Sugar Test Strips can eliminate interference from oxygen variations and non-glucose sugar such as maltose and galactose, providing you with the most reliable and accurate results. They provide full warranty and is suitable for self testing. Each strip can be used ONCE ONLY!. A test strip consists of the following parts: Target Area: Where a blood drop or control solution is touched. Confirmation Window: To confirm if sufficient blood drop or control solution has been applied to Target Area. Contact Bar: The end of the test strip is to be inserted into the test port (top side facing up). On each test strip the target area contains reaction chemicals. When blood is applied to this area, a chemical reaction takes place, then a transient electrical current is formed. The blood glucose concentration is calculated based on the electrical current detected by the meter, then the result is showed on the display. The test measures glucose from 20 mg/dL (1.1mmol/L) to 600 mg/dL (33.3mmol/L). The Rossmax HS200 Test Strip is calibrated to display the equivalent of plasma glucose values to allow easy comparison of results with laboratory methods.

• Offers 5 seconds fast test time, that too with a small quantity blood sample
• Results are not affected by oxygen, galactose & maltose
• Offers individuals with type 1 or type 2 diabetes around-the-clock glucose readings
• Provides real-time, dynamic information about the speed and direction (trending higher or lower) of your glucose levels
• Provides information necessary for you and your healthcare provider to determine how well your treatment plan is working
• Helps you prevent serious complications from undetected low or high glucose levels
• Reduces anxiety associated with not knowing how well you are managing your diabetes between visits with your healthcare provider
• Increases motivation to practice healthy habits
• Helps you determine if your glucose levels are too high or too low to drive or operate heavy machinery

• Read the user manual for detailed usage instructions
• Install the batteries, set the date and time in the Rossmax HS200 Blood Sugar Monitor (instructions in the manual provided)
• To prepare the strips: Wash hands using soap and warm water. Rinse and dry thoroughly. Insert the test strip, top side facing up into the test port. The meter will automatically turn on. System checking will appear. A beep will sound, you can select the meal indicator for marking the test as pre-meal test , post-meal test , or no marker. Note: Check if your meter displays the unit of measurement you are accustomed. A blood sample can now be obtained. Note: The meter will shut off automatically after 2 minutes without any action
• Preparing the Lancing Device and Obtaining a Blood Sample: Unscrew the lancing device cap. Place a lancet into the lancing device. Twist and pull to remove the protective lancet cap to expose the sterile needle, save the cap for later use. Screw the lancing device cap back on. Select the skin penetration depth preferred. Pull the barrel back until you hear a 'click' sound. Place the lancing device softly against the finger, palm, or forearm, and press the release button to obtain a blood sample. Now unload and the dispose used lancet in an approved container (instructions in the manual provided)
• Applying a blood sample to the test strip to perform a test: After obtaining a blood sample, discard the first drop to prevent contamination. Introduce the tip of the test strip to the drop of blood. Blood sample will be automatically drawn into the test strip. Hold the tip of the test strip touching the blood drop until the meter beeps. As soon as the blood has completely filled the confirmation window of the test strip, the meter will start a countdown. The test result will appear on the display after 5 seconds and will be automatically stored into the meter memory. After the test result appears and if there is no further test, the meter will automatically turn off after 2 minutes. If applying a blood sample of reduced volume, the error code (E-7) will appear on the display (Error code is described clearly in "Error Messages" section of the instruction manual).
• STORAGE: Storage conditions : Temp: 4C~30C, do not refrigerate. Re-cap immediately. Always close cap tightly.